Black Bar Ends

BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD

BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD
BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD
BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD
BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD
BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD

BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD    BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD

BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD. BDS Suspension's revolutionary spring loaded, full-floating RECOIL traction bar system is engineered to improve traction and limit axle wrap without limiting suspension travel or decreasing ride quality. BDS RECOIL traction bars offer you the freedom to tune the spring compression for optimal performance on-road, off-road, towing, or competition pulling. These traction bars can be used on stock height or lifted trucks and work with both lift blocks and replacement leaf spring kits.

BDS RECOIL traction bars are built to the highest standards for the ultimate performance on and off-road. The bars are fabricated from 2" OD x 3/16" wall steel tubing with a threaded bung welded in toward the axle and a CNC machined end at the frame. The axle mount uses the tried and true BDS large forged flex end and jam nut to take whatever abuse you throw at it.

BDS forged flex ends use a forged housing with large 1-1/4 -12 threaded shank, single sided snap ring and 1-piece flex ball for up to 15-degrees of misalignment in either direction. At the frame end the bar uses a durometer specific polyurethane bushing installed that free floats in the traction bar utilizing dual stage internal compression springs and UHMW polyurethane bearings. Both ends are greaseable and rebuildable. Fully assembled the RECOIL traction bars are 60" long and mount to the vehicle using fabricated 1/4" steel brackets.

Bracket kits are vehicle specific. The frame brackets install by drilling mounting holes for the brackets while the axle brackets install using a set of u-bolts. The traction bars and mounting brackets use a durable gloss black powdercoat finish. These new RECOIL traction bars are built to the highest standards featuring quick and easy adjustment while installed on the vehicle. To adjust spring compression, use the supplied spanner wrenches at the axle to loosen the jam nut.

From there the main bar can be rotated to load or unload the springs at the frame side of the bar. Using the concave end of the wrench handle against the frame end check the location of the end of the main bar in relation to the notches on the wrench to verify the load on the springs, the shorter the distance the more loaded the springs are. Repeat this process on the other traction bar and use the wrenches to tighten down the jam nuts and you are ready to go! Adjustable axle wrap control utilizing dual-stage resistance springs. Full floating traction bar design will not bind throughout the full range of wheel travel and/or hinder suspension articulation. Does not adversely affect ride quality when springs - particularly when resistance springs are adjusted to still be active.

Spring preload can be adjusted on the vehicle without disassembling the traction bar. Adjustments can be made for optimum performance over a wide range of uses/terrain.

(On Road - Unloaded, Towing/Hauling, Off-Road, Competition pulling). Traction bar ends are greaseable and rebuildable.

Mounting brackets are bolt-on, only requiring minor drilling for frame mount installation. Fits 0-6 of rear lift. Fits 4 Rear Axle Models Only. Will NOT work on standard cab models. Will fit Single and Dually rear wheel models.

1/2" x 4" x 5-3/4 Round U-bolt. Bolt Pack (Traction Bar Hardware).

9/16"-12 x 4" Bolt Grade 8. 5/16"-18 x 1" Self-Tapping Hex Head Bolt. 1/2-13 Nut (Non-Locking) - Grade 8. 1/2"-13 x 1-1/4" Bolt Grade 8. 1/2-13 Serrated Flange Lock Nut. This item is in the category "eBay Motors\Parts & Accessories\Performance & Racing Parts\Auto Performance Parts\Chassis, Suspension & Brakes\Lift Kits & Parts". The seller is "trendsauto" and is located in this country: US. This item can be shipped to United States, Canada.
  • Manufacturer Part Number: 121408
  • MPN: 121408
  • Brand: BDS
  • Warranty: Lifetime
  • Fitment Type: Performance/Custom
  • Type: Recoil Traction Bar
  • Part Type: Mounting Kit
  • Lift Height: 0\
  • Color: Black
  • Material: Steel
  • Country/Region of Manufacture: United States
  • Placement on Vehicle: Rear
  • Feature 1: Fabricated from 2\
  • Feature 2: Threaded bung welded
  • Feature 3: Large 1-1/4\
  • Feature 4: Both ends are greaseable and rebuildable
  • Feature 5: Fully assembled RECOIL traction bars are 60\
  • Feature 6: Bracket kits are vehicle specific
  • Feature 7: Mounting brackets are bolt-on
  • Feature 8: Adjustable axle wrap control
  • Feature 9: Utilizing dual-stage resistance springs
  • Feature 10: Made in the USA

BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD    BDS 121408 Recoil Traction Bar Mounting Kit for Silverado Sierra 2500 HD 3500 HD