V Bar w/Quick Release Ends. MADE IN USA V RACKS. THE BEST SOLUTION FOR TRANSPORTING YOUR OUTRIGGER CANOE OR SURF SKI.OUR PRECISION PRODUCTS ARE MADE FROM AIRCRAFT GRADE 6061 T6 ALUMINUM AND TYPE 3 AIRCRAFT ANODIZING. There is no easier, safer, or faster system for transporting your craft. Your hull is supported in its natural shape by 4 inch wide foam covered aluminum cradles. There are no faster loading systems, set your boat in the V Cradle, secure the two bungee cords, secure the cam straps, mount the red flag, and go. Takes less than a minute. Be safe and have peace of mind, knowing your boat is secure, safe, and well supported. Our V racks are made in our shop, we use 6061 Aircraft aluminum, Type 3 aircraft anodizing, and US made stainless steel fasteners. No one makes V racks like us! Our standard V bar with quick release ends utilizes a 7 foot V bar, the quick release ends are 18 inches long (9 inches each), which provides an overall length of 8.5 feet. For some applications, like the Jeep Wrangler pictured, a longer 8 foot bar with quick release ends is needed to cover the span, providing an overall length of 9.5 feet. Precision laser cut quick release inserts provide a tight, rattle free connection. Many cars have horizontal bars that run the length of the vehicle. To mount our V Bar, you also need. Which run from side to side and attach to your vehicles. Our standard hardware will fit cross bars up to 3.5 inches wide and 1.5 inches tall.
If you dont have horizontal bars to begin with, these must be installed as well. Made in the USA from aircraft grade 6061 aluminum and anodized with Type 3 aircraft anodiizing. All hardware, bungee tie downs, camstraps, and safety flag included. Hardware is Made in USA stainless steel.
HOW DO Ocean Pacific RACKS MOUNT TO MY CAR? To mount our V Bar, you also need sturdy crossbars which run from side to side and attach to your vehicles horizontal bars.
WHAT LENGTH BAR LENGTH DO I NEED. WHAT ABOUT QUICK RELEASE ENDS? Standard 8 foot V bar with bolt on Vs is the simplest. Vs can be removed in 5 minutes with wrench and socket, leaving only the low profile 1.5 x 3 inch flat black bar.
While it is best to have the V bar centered on your crossbars, you can move it up to 1 foot forward of center to clear the opening truck/hatch on small SUVs and Hatchbacks. If the bar is too long, consider our Short Bar with Quick Release ends.7 foot bar with Quick Release Vs allows removal of the Vs in seconds by use of a quick release pin, no tools necessary. Total length is 8.5 feet with ends in place. 5.5 foot Short Bar with Quick Release Vs is for shorter SUVs, hatchbacks, and shorter vehicles. With the Vs removed, the shorter 5.5 foot bar allows for the opening of the rear truck/hatch/lift gate. Total bar length is 7 foot overall with ends installed, plenty of length to mount a 21 foot boat. WHICH VS DO I NEED? Standard Vs will work for all OC1s, OC2s, shells, racing kayaks/surfskis and sea kayaks. Intermediate size surf skis and kayaks work better with the wide Vs. Boats over 18 inches wide need the wide Vs. The item "Surf Ski V Bar Roof Rack Top Carrier withQuick Release Ends Made in USA" is in sale since Tuesday, November 19, 2019. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Exterior\Racks". The seller is "crossbowusa" and is located in Las Vegas, Nevada. This item can be shipped to United States, Canada, United Kingdom, Australia, Mexico, Germany, Japan, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, Belgium, France, Ireland, Netherlands, Poland, Spain, Italy, Austria, New Zealand, Switzerland, Norway, Ukraine, Croatia, Bermuda, Guernsey, Gibraltar, Iceland, Jersey, Liechtenstein, Luxembourg, Monaco.